Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Liner & Rebuild Cost in Murfreesboro?
Chimney liner repair in Murfreesboro typically runs $1,100 to $3,800, and a full chimney rebuild usually falls between $8,500 and $28,000 depending on how much of the stack has to come down. A stainless flexible liner install is most often $1,800 to $4,200, while HeatShield resurfacing of an existing flue tends to land at $1,400 to $2,600. We set every price per job with a written estimate, and that written estimate is the final word on what you pay.
Most Murfreesboro jobs sit at the lower half of those ranges when the flue is straight and the crown is still sound. Older houses near the Public Square or along the streets close to Middle Tennessee State University often need more, because the chimney was built for a wood fire and now carries a gas insert or a stove with different venting demands. We answer 24/7 at (844) 372-0461, and every estimate is free.
Chimney Liner & Rebuild Cost Breakdown (2026)
Here’s how the numbers shake out line by line. Treat these as typical estimates for the Murfreesboro market, not quotes. The written estimate is what sets your actual price.
| Line item | Typical Murfreesboro range | What it covers |
|---|---|---|
| Stainless flexible liner install (single flue) | $1,800 – $4,200 | DuraFlex or Olympia Chimney liner sized to the appliance, insulation where required, top plate and cap |
| HeatShield resurfacing (liner restoration) | $1,400 – $2,600 | Poured or troweled resurfacing to restore a cracked or spalled clay flue without pulling a full liner |
| Chimney cap and crown repair | $350 – $1,200 | Gelco or Copperfield cap, crown repair, drip edge, waterproofing at the top |
| Partial rebuild (upper courses and crown) | $8,500 – $14,000 | Tearing down and rebuilding the section above the roofline, new cap, new crown |
| Full rebuild (ground to top) | $18,000 – $28,000 | Full teardown and rebuild, flue relining, flashing, crown, and cap |
| Flue tile replacement | $600 – $1,900 | Removing cracked clay tiles and relaying new ones, per section |
| Chase cover / venting correction | $400 – $1,300 | Famco and Gelco chase covers and venting fixes for wood stoves and inserts |
| Inspection before the work | Free with the estimate | Documented assessment of the flue, crown, cap, and firebox |
What pushes a job up: a flue with an offset that needs a flexible liner to snake around a bend, a chimney with multiple flues (each one is its own liner), or a stack that’s leaning enough that we have to rebuild from the roofline down. What keeps it down: catching a cracked flue early enough for HeatShield resurfacing instead of a full liner, and a crown that can be repaired instead of replaced. Steel liner prices also move with the metal market, so a quote from last year isn’t a reliable guide to this year.
Rebuild pricing is the one most homeowners underestimate. A rebuild isn’t a repair with new brick on the face; it’s masonry that has to be taken down, tied into the structure, rebuilt course by course, and then relined. That’s why a partial rebuild costs several times what a liner does.
What Affects Chimney Liner & Rebuild Pricing in Murfreesboro
Six things move the number more than anything else:
- Whether the flue can be saved or has to be relined. HeatShield resurfacing restores a clay flue that’s cracked or spalling but still structurally sound. When the flue is failing badly or the wrong size for the appliance, a stainless liner is the answer. That decision alone can swing the job by a couple thousand dollars.
- Flue shape and offsets. A straight flue is quick work. A flue with an offset or a bend needs a flexible liner sized and installed carefully. That’s where DuraFlex and Olympia Chimney products earn their keep, and it’s the work that separates a chimney specialist from a sweep-only operation.
- How much masonry has to come down. Murfreesboro has a lot of chimneys built for wood fires that now serve gas inserts or stoves, and those chimneys were often never lined for the new appliance. The further the water damage has spread above the roofline, the more courses come down. Rebuilds here are common on older homes where the crown has been letting water in for years.
- Freeze-thaw cycles. Middle Tennessee winters swing above and below freezing repeatedly. Water gets into brick and mortar joints, freezes, expands, and spalls the face off. That repeated cycling is the main reason Murfreesboro chimneys need crown and cap work long before a northern chimney would.
- Number of flues. A chimney serving a fireplace and a furnace has two flues, and each one is priced separately. That’s true on plenty of homes around Murfreesboro, especially where a gas furnace vents into the same stack.
- Access and roof pitch. A steep roof, a chimney on a tight side yard, or a stack that’s hard to reach safely all add labor. So does a chimney that has to be scaffolded rather than reached from a ladder.
How to Save on Chimney Liner & Rebuild
The single biggest saving on a liner job is catching the problem before it becomes a rebuild. A sweep and inspection while the flue is still sound is cheap next to relining, and a HeatShield resurfacing is usually far less than a full stainless liner when your flue qualifies. We show you what we find and let the photos make the case, so you’re not guessing whether the work is real.
Four practical moves that keep the bill down:
- Fix the crown and cap now. A cracked crown lets water in, and water is what turns a small repair into masonry work. Gelco and Copperfield caps and a sound crown protect the whole stack.
- Get the liner sized right the first time. An oversized or undersized liner wastes money and can vent the appliance poorly. Correct sizing is part of the estimate, not an add-on.
- Bundle sweep, inspection, and repair. We handle all three under one company, so you don’t pay twice for someone to look at it and someone else to fix it. The inspection is documented and comes with the estimate.
- Get several written estimates and compare scope, not just price. A quote that lists the liner, cap, crown, and insulation line by line is worth more than a single number with no detail.
Call (844) 372-0461 for a free estimate. Our technicians have up to 9 years of experience, and we work with the same professional brands chimney contractors specify: DuraFlex liners, HeatShield resurfacing, Olympia Chimney, Gelco, Famco, and Copperfield components. That mix means we can offer a repair path instead of defaulting to the most expensive option. If you want a sense of who we are first, start with Goodwin Chimney Sweep.
Can a Chimney Liner Be Repaired Instead of Replaced?
Yes, in many cases. If the clay flue is cracked or spalling but still straight and structurally sound, HeatShield resurfacing can restore the flue lining without pulling a full stainless liner. That’s the repair path most basic sweep companies can’t offer, and it typically saves $400 to $1,600 compared with a full liner.
Resurfacing won’t help a flue that’s the wrong size for the appliance, badly offset, or where the masonry itself is failing. In those cases a stainless liner through DuraFlex or Olympia Chimney is the honest answer. We tell you which one applies after we’ve looked, and we show you why.
Is a Chimney Rebuild Cheaper Than a Liner Replacement?
No. A rebuild is the more expensive option, usually by a wide margin. A liner install typically runs $1,800 to $4,200, while a partial rebuild starts around $8,500 and a full rebuild can reach $28,000. A rebuild is only the right call when the masonry itself has failed and a liner can’t fix it.
The decision comes down to what’s failing. If it’s the flue lining, a liner or resurfacing solves it. If it’s the brickwork, the crown, or the structure of the stack, no amount of liner work will hold. Our inspection sorts that out, and the written estimate tells you exactly which work is needed and why.
What Causes Chimney Damage in Murfreesboro?
Water and freeze-thaw cycling cause most of it. Brick and mortar absorb water, Middle Tennessee winters freeze and thaw repeatedly, and each cycle spalls the brick face and opens joints a little wider. A failed crown is usually where it starts, because it lets water straight into the top of the stack.
Creosote and the wrong appliance for the flue cause the rest. A wood stove or gas insert running through an unlined or undersized flue builds up creosote and vents poorly. If you’ve changed what you burn and not had the flue checked, that’s worth a look before the next heating season. For local context on the market and the neighborhoods we work in, see Murfreesboro.
Do I Need a Permit for a Chimney Rebuild in Murfreesboro?
Most cities require a permit for structural chimney work, including a rebuild, and the rules can vary by project. Murfreesboro follows the state building code, so ask the city’s building department or your contractor to confirm what your specific job needs before work starts. Liner and resurfacing jobs sometimes fall outside permit scope, but it depends on the work.
Either way, a written estimate should spell out the scope so you and the city are looking at the same thing. If a contractor won’t put the scope in writing, that’s a reason to keep looking.
How Long Does Chimney Liner & Rebuild Work Take?
A stainless liner install is usually a day’s work. HeatShield resurfacing takes a day plus cure time. A partial rebuild runs several days, and a full rebuild can take a week or more depending on weather and how much masonry comes down. Rain stops masonry work, so Middle Tennessee spring weather can stretch a rebuild.
We book the work when we give you the estimate so you know what to expect. If a liner fails inspection or a rebuild is needed before winter, the earlier you call the more room there is in the schedule. Reach us at (844) 372-0461.
Is Chimney Work Safe to Do Yourself?
Liner and rebuild work is not a do-it-yourself job. It involves heights, masonry, and the flue that carries combustion gases out of your home. A badly installed liner can vent carbon monoxide back into the house, and masonry that isn’t tied in correctly can fail. This is work for a trained professional, and we recommend you treat the height and the flue with that respect.
What you can do safely is look from the ground: check whether the crown is cracked, whether the cap is missing or rusted, and whether the mortar joints look washed out. Those are the signs worth a call. Leave the flue itself to a sweep and inspection.
FAQs – Chimney Liner & Rebuild Cost
How much does a chimney liner cost in Murfreesboro?
A stainless flexible liner install in Murfreesboro typically costs $1,800 to $4,200. That includes sizing to your appliance, the liner itself, insulation where needed, a top plate, and a cap. HeatShield resurfacing, when the flue qualifies, usually runs $1,400 to $2,600. Call (844) 372-0461 for an exact quote, and the estimate is free.
How much does a chimney rebuild cost in Murfreesboro?
A partial rebuild typically runs $8,500 to $14,000, and a full rebuild from the ground up usually lands between $18,000 and $28,000. The number depends on how much masonry comes down, whether the flue needs relining, and how hard the stack is to reach. The written estimate sets the final price. Call (844) 372-0461 to book a free assessment.
Is it cheaper to repair a chimney liner or replace it?
Repair is usually cheaper. HeatShield resurfacing often costs $400 to $1,600 less than a full stainless liner and restores a sound clay flue without pulling a new liner. It only works when the flue is still structurally sound and correctly sized. If the flue is offset, undersized, or failing badly, replacement is the honest answer. Call (844) 372-0461 and we’ll tell you which applies after we’ve looked.
Can you come today?
Often, yes. Same-day service is possible when the schedule allows, and we dispatch Sunday through Friday from 7am to 7pm. We answer 24/7, and a call outside dispatch hours is booked into the next opening. Call (844) 372-0461 for a free estimate.
Who should I hire for chimney liner and rebuild work in Murfreesboro?
Hire a chimney specialist who installs professional-grade materials and puts the scope in writing. Ask whether they work with recognized liner brands like DuraFlex and Olympia Chimney, whether they can do HeatShield resurfacing, and whether their inspection is documented. A sweep-only operation can find a problem it can’t fix. We do sweep, inspection, and repair under one company, so you deal with one crew from the first look to the finished repair. Call (844) 372-0461 for a free estimate.
What Happens When You Call
We answer 24/7, and we’ll ask what you’re seeing: smoke backing up, a cracked crown, a cold fireplace, or a flue that hasn’t been checked in years. Then we schedule a visit to look at the flue, crown, cap, and firebox, document what we find, and put a written estimate together with the scope itemized. No pressure to take the most expensive path, and no surprise charges. Fast dispatch from 7am to 7pm, Sunday through Friday.
A clean flue isn’t just maintenance; it’s the difference between a good fire and a house fire, and a chimney that needs rebuilding is the same story told in brick. If you’re weighing a liner against a rebuild, get the honest answer first. Call (844) 372-0461 for a free estimate. We answer 24/7.
Written by the team at Goodwin Chimney Sweep.
Pricing reflects the Murfreesboro market as of 2026. Goodwin Chimney Sweep offers free estimates – call (844) 372-0461.
What Our Customers Say
"Drop cloths everywhere, HEPA vac, and not a speck of soot on the carpet. I'd been dreading the mess for nothing."
- Eric Ackerman"Swept it, capped it, and installed a proper damper. The downdraft smell in the summer that we'd lived with for years is gone."
- Alicia Dawson"Level two inspection before we bought the house. The report was detailed enough to use as a negotiating point and he explained every photo in it."
- Rosa Vargas